CONSTRUCTION AND ENGINEERING PRODUCTS
SPEC-CRETE
Resin Cure Resin based concrete curing compound.
To provide a resin membrane on the surface of newly placed concrete to retain moisture for effective curing to take place.
CONCURE WB
Water based concrete curing compound.
To provide a membrane on the surface of newly placed concrete to retain moisture for effective curing to take place. Non-toxic and non-flammable.
SPEC-CRETE C.R.A
Chemical form release agent.
To provide quick clean and easy stripping of moulds and formwork to ensure high quality, fair faced and stain free concrete.
KONKLEEN
Concrete cleaning, removing and etching agent.
Konkleen is a combination of acid based material, corrosion inhibitors and dispersing agents.
It is used for the removal of mortar and plaster runs, droppings and stains from brickwork and concrete surfaces.
Also for the removal of hardened concrete from tools and equipment or rust and mill scale from steelwork. For cleaning concrete and also clay tile floorings.
NITOFLOR HARDTOP "T"
Monolithic surface hardening compound for fresh concrete floors.
Nitoflor Hardtop provides a highly abrasion resistant surface to fresh concrete floors by the dry shake, trowel-in method, which ensures that the hard wearing surface bonds monolithically to the base concrete. It is ideally suited to all industrial areas subjected to heavy traffic.
NITOFLOR
LITHURIN Permanent concrete hardening and dustproofing compound.
Lithurin is supplied as a powdered crystal for dilution on site. It is used as a surface hardener of new and existing concrete to prevent dusting, minimise wear, and reduce attack by certain chemicals.
SPEC-CRETE SUPERSEAL B66
Hard wearing acrylic floor sealer.
Superseal B66 is a solvent based acrylic floor sealer. Ideal for use in industrial applications, Superseal will provide a hardwearing, attractive, dustproof surface.
CONBEX 100
Plasticised, expanding grout admixture.
Conbex 100 is a powerful admixture which is a combination of a strong plasticiser and an expanding agent. When combined in a cement/water or sand/cement/water mix, results in a low water/cement ratio with expansive properties.
CONBEXTRA GP
High performance, expansive cementitious grout.
Conbextra GP is a general purpose cementitious grout.
It can be used from a free flow to a dry pack consistency with only a variation of the water content. High early and ultimate strengths. IDEAL as a General Purpose Construction Grout.
CONBEXTRA HF
Highly fluid, shrinkage compensated cementitious grout. Meets & Exceeds Corps of Engineers CRD-C-621-82A and ASTM C1107-91(Type C)
Conbextra HF is a high performance shrinkage compensated cementitious grout. It is a premium product used for free flow grouting over a range of application consistencies. Advantages of this product include: dual shrinkage compensation, high early and ultimate strengths, non metallic, hydrogen and chloride free.
CONBEXTRA TS
Highly fluid, dual shrinkage compensated, thick section cementitious grout.
Conbextra TS is a high performance dual shrinkage compensated cementitious grout. It is a premium product used for free flow grouting of thick sections up to 500mm thick, over a range of applications. Advantages of this product include: dual shrinkage compensation, high early and ultimate strengths, non metallic, hydrogen and chloride free, and low heat of hydration.
CONBEXTRA Injection
Low viscosity free flow epoxy grout
Conbextra injection is a solvent free low viscosity epoxy grout for grouting gap widths from 0.25 mm to 9 mm.
Its high fluidity also makes this material ideal for crack injection and crack filling on a horizontal surface.
CONBEXTRA EPR
Non shrink solvent free multi range epoxy grout
CONBEXTRA EPR is a three part 100% solids epoxy grout, designed for free flowing dynamic grouting where a variety of grout thicknesses will be encountered.
Suitable for use from 10 - 120 mm thick gaps. Available in a Tropical grade for low exotherm, as well as a Thick Section grade for low exotherm thick sections up to 500mm thick.
LOKSET P40
Resin based bolt and anchor grout.
Lokset P40 is a polyester resin grout designed for high strength, corrosion resistant anchoring of bolts and bars into concrete, rock, masonry or brickwork, where high speed of application and early loading is essential.
Lokset P40 is a thixothropic grade and can be used in horizontal, overhead or downward sloping holes. Once mixed, Lokset can be used under water or in wet holes or environments. Commonly used with rebar starter bars, foundation bolts, base plates and ground anchors, etc.
THIOFLEX 600
Two part polysulphide joint sealant. Approvals: BS 4254 1983, BS 6290 1988, US Federal specifications TT-S 00227E1969, UK water bylaws scheme listing #8810510, DIN 18540 1980, DTP specifications for highway works clause 1017.
Two part high performance long life joint sealant, for expansion joints in brickwork, concrete and stone. Accommodates continuous and pronounced cyclic movements. Suitable for underground reservoirs, water towers and water treatment works. MAF - 25%
COLPOR 200 PF
Pitch free, heavy duty pavement joint sealant. Approvals: BS 5212-1990, DTP specifications for highway works 1991 clause 1017.4, US Federal specs. SS-S-200E 1984. Fuel, oil and hydraulic fluid resistant.
Cold applied, pourable joint sealant for concrete pavement areas.
Ideal for concrete roads, airports, parking lots, etc. MAF - 25%
FLAMEX ONE
One part, flexable intumescent sealant
FLAMEX ONE in a one part emulsion based joint sealant that sets quickly, has a 10% movement for use around fire door frames and fire protection boards.
CONFLEX
Bitumen impregnated fiberboard expansion joint filler.
For forming joints in in-situ concrete structures or between precast concrete components.
EXPANDFOAM
Closed cell joint backer rod.
For use as a joint filler and backer and also as a bond breaker and former for elastomeric sealants. Prevents three sided adhesion of the sealant.
MULSEAL DP
Bitumen/latex emulsion waterproofing and dampproofing compound
Mulseal DP is a one part bitumen latex emulsion for use as a waterproofing compound, vapour barrier, damp proof membrane and protective coating.
SUPERCAST HYDROFOIL / SUPERCAST WATAFOIL
PVC Waterstops
PVC waterstops cast into and across in-situ concrete joints to prevent ingress of or loss of water through joints in water retaining or water excluding structures.
SUPERCAST WATAFOIL is centrally placed for construction joints and SUPERCAST HYDROFOIL is centrally placed for both construction and expansion joints.
REARGUARD S
PVC Waterstops
PVC waterstops cast into and across in-situ concrete joints to prevent ingress of or loss of water through joints in water retaining or water excluding structures.
SUPERCAST REARGUARD S is externally placed for both construction and expansion joints.
SUPERCAST SW10
Hydrophillic Waterstops.
Problem solving swellable waterstops cast into concrete joints to prevent ingress of or egress of water.
Typical use areas include joints between old to new concrete, where the designed waterstop has been forgotten or omitted, or in difficult bends and angles where the flat profile of a PVC waterstop cannot work.
SUPERCAST SWX
Hydrophillic paste
Supercast SWX is a grey elastomeric, water swellable gun applied paste.
For use in difficult areas where either a PVC or preformed hydrophillic cannot work, or also as an adhesive for Supercast SWX
VEDAX PLUS
Two part cement based waterproof coating for potable water tanks.
Vedax Plus is a two-part, polymer modified cementitious coating that has been especially developed for use as an internal coating for waterproofing potable water retaining structures.
It also retains flexibility when immersed.
INTEGRA
One part Cementitious waterproofing system
INTEGRA is a one part cementitious waterproofing compound that utilizes the chrystalisation migration process. Suitable for either positive or negative waterproofing.
